18V-32VDC BLDC Water Pump For Coolant, Widely Used in Immersion
Fluids, Cryptomining Liquid Cooling System and Data Centre Cooling
Circulation System.
Features
- Centrifugal pump
- Magnetic force transmission
- High efficiency brushless DC motor, low power consumption, high
efficiency, long service life.
- With wide range operating temperature
- PWM signal speed controlling
- Diagnostic signal output
- With constant flow controlling
- Reverse polarity protection
- Dry running protection
- Over Voltage, over current protection
- Overload, over temperature protection
Technical description (related parts in contact with the liquid)
Pump head housing: Die casting aluminum alloys
Impeller: PPS+GF Shield cavity: PPS+GF
Shaft sleeve: carborundum composite materials Shaft: stainless
steel(3CR14) shaft
Magnet housing: PPS plastic capsulation Seal ring: EPDM
EMC: Grade 3 Noise:≤61dB
Driving device (Including motor)
Driving rotor: PPS plastic capsulated magnet
Screws and nuts: SUS 304 stainless steel
Driving Motor : brushless DC motor
Motor wire frame :PPA GF
Pump housing: Die-casting aluminum case with sandblasting and
anodizing +PE powder coating..
Bracket: steel
Bracket hoop: US 304 stainless steel
Waterproof based on IP68 rating (en60529)
Connector model: AMPHENOL C-ATP04-4P-PD01NFK(matched Plug: AMPHENOL
C-ATP06-4s-RD01NFK)
Nozzle diameter:25mm (1 inch)
Mounting instruction
OWP-BL43-440T series pumps are centrifugal pumps which require
pre-filled,
The pump installed in the lowest position of the system to ensure
that the impeller is always immersed in the liquid, or pre-filled
the pump before power on .
1: Pump should not be dry-running, even though it can dry-running
for 15 minutes (after 15 minutes dry-running, it will automatically
stop), Dry running will makes noise, also increasing abrasion to
the shaft and shaft sleeve.
2:Use the recommended diameter pipe connecting the pump inlet, if
you use a smaller diameter hose pump inlet, Due to the negative
pressure in the pump, the outside air easier enter to the pump
through the pipeline, it will make the pump performance
degradation, and also the air bubbles make damage to the pump.
3: As viewed from the pump inlet direction, the impeller rotates
clockwise (see the arrow on the outlet port).
4: The pump can be installed vertically or horizontally mounted
(see figure 1 ) When installed vertically, the outlet port should
be upward .
5:In order to avoid the dry- running (air get stuck in
impeller),the water pump outlet port should be vertical or in the
upper of the impeller. (see figure 1 )
6: The connected pipe should be vertically mounted (or no elbow in
20cm )to make the air discharged easily, the outlet pipe should not
be used less than 90 degrees elbow (see figure 2).
7: Can't use the seawater or other heavy pollution with big grain
impurity liquid as the liquid medium .
Figure 1 Figure 2
Temperature parameter
Medium liquid temperature: -40℃ to +85℃ (-40°F to + 185°F)
Working ambient temperature: -40℃ to +120℃ (-40°F to +248°F)
Storage temperature: -40℃ to +70℃ (-40°F to +158°F)
(up to 100 ℃, but it will shorten the service life)
System pressure
-0.2 to 2.5 bar ( 100℃ (212°F).
The service life is more than 20,000 hours based on the rated
voltage and 36℃(86°F) ambient temperature.
Voltage range
Rated 24V water pump, workable range 18V - 32V
Although the motor can be used in a wide range of voltage and
temperature, but excessive or too low voltage and temperature will
affect the service life of the motor, the pump cannot be exposed to
thermal radiation ambient.
Medium liquid: liquid mixture (Water with below 60% glycol)
Electrical parameter
Working Voltage(VDC): 18V-32V(24VDC)
Rated power 400W
Rated flow(L/H): Q=3000L/H, H=20m
Dimensions(mm): 185*90*155
Weight(g): 2200g
Parameter Curve
External dimension
